The vast majority of W210 owners have very few or only minor problems with their Benzes. Most of the issues these cars have, if any, are minor and best described as irritations. Some the issues are far more serious, but are relatively rare. Here’s a list of some of the common and not-so-common problems with the W210 E-class.
Major Problems
Rust
Some of the E-classes made it out of the factory without propery body panel sealing. This leads to rust in short order — not exactly something you want to see on your shiny Mercedes! The rust is usually pretty easy to spot if you know where to look. When inspecting a prospective car for purchase, look for rust:
- Under the door seals — Peal back the inside edge of the door seals and look for rust.
- On the trunk lid around the latch
- Front spring perch (rare, but serious safety issue! 4Matics not affected) — Rust in the inner fender due to improper sealing weakens the attachment for the front coil spring. If the rust is severe, the spring perch may tear away from the body. If this breaks free at 90 MPH on the interstate, the aftermath won’t be pretty. Turn the wheel all the way each direction and stick your head in the front wheel well to inspect for rust. If there’s no rust, you should be okay. Taking a few moments to check for spring perch rust before you buy should help keep your entrails off the pavement.
Harmonic Balancer: 1998 to 2002 V6 and V8 models only
The main crankshaft pulley on the front of the engine, called the harmonic balancer, on the 1998 to 2002 V6s and V8s deteriorates with age and mileage. If the pulley wears out, it will slide out of position and grind its way through the front of the engine (timing chain cover), the oil pan, and possibly destroy the radiator. Not good for morale, since several thousand dollars to fix all the damage!
The good news is that replacing the pulley before it flies apart only costs $150-$250. The signs of failure are obvious. Check the pulley for separation of the rubber insert from the main body. If it appears to be coming apart, tow it (don’t drive) it to the shop and get it replaced.
Mercedes issued a recall on the harmonic balancer last year. Although the replacement harmonic balancer has been redesigned, there are some reports of it failing as well. Plan to replace the harmonic balancer every 60,000 miles or so. A little preventative maintenance goes a long way.
Head Gasket: 1996 & 1997 E320 only
The head gasket is the Achilles’ Heel of the otherwise superb M104 3.2L engine in the 1996 & 1997 E320. The head gasket tends to develop a leak every 70,000 to 100,000 miles. Usually the leak is visible on the outside of the motor. It’s important to fix this to avoid mixing coolant & oil. Plan to spend about $1100-$2000 to have this replaced, depending on the shop.
Intermediate Problems
Window Regulators
This is like a chapter straight out of A Tale of Two Junkyards. Go to an American junkyard, and you’ll find mountains of cars with blown engines and fully operational power windows. Take a trip to a German junkyard, and you’ll find mountains of Mercedes with healthy engines and broken windows.
In case I wasn’t clear, the power windows are a trouble spot on the W210 and most all Mercedes. The window regulators — the part that connects the window motor to the window glass — are poorly designed, particularly the ones in the rear. They break often. When they break, the window glass falls down into the door and you can’t get it back up. Plastic and duct tape don’t belong on a Mercedes, so it’s not something you can postpone fixing.
If you use your rear windows regularly, you’ll probably be replacing the regulators frequently. The part costs $80, and if you’re slightly mechanically inclined, you can replace it yourself. Otherwise it’ll cost you about $200-$300 each time. It’s financially prudent to avoid rolling down the rear windows.
A/C Receiver-Drier (rare), Compressor (rarer), or Evaporator (very rare) leaks
If and when they conspire, the rear window regulators and a leaky A/C have real potential to make you a sweaty mess. The A/C receiver-drier removes moisture and contaminants from the air conditioning system. Think of it like a filter. If your A/C won’t hold a charge, it’s likely the receiver-drier that’s leaking. Replacing this part is inexpensive.
If you’re an unlucky person, you may at some point have a leaky A/C compressor. The A/C compressor part costs about $600. Any time you crack open the system, you must also replace the receiver-drier. Parts and labor for a new compressor will run you about $1100. Compressor failure isn’t too common.
If you’re really, really unlucky, your A/C evaporator may develop a leak. This isn’t a nightmare to replace like the S-class evaporator. More like a bad dream. Replacement involves removing the dash. Leaks in the evaporator are rare enough that I feel bad about listing it here. Might scare you or something.
Wet Transmission Control Module
The quick disconnect on the transmission wiring harness sometimes leaks fluid. The fluid gets pressurized and shot up through the bundles of wires into the transmission control module. Voila! You have a flooded transmission control unit. It’s important to periodically inspect this to make sure it’s not leaking. If it is, you can often inexpensively repair the problem by replacing the harness. If the fluid fries your control unit, plan on shelling out some money.
Catalytic Converters
The catalytic converters have a procilivity to wear out after about 60,000 to 100,000 miles. The catalyst material inside breaks apart and rattles around inside the body of the converter like loose marbles. If the cats clog, the exhaust backpressure can hurt your engine. You can tell your cat needs replacement if you can hear what sounds like marbles rattling when your engine is running. Replacement catalytic converters cost about $800 for each side from the dealer
Note that sometimes the weld on a small bracket further down the exhaust pipe may break, causing the pipe to rattle and transmitting the noise along the pipe. The broken weld may be very difficult to spot. The sound of this broken bracket may mimic that of failed catalytic converters. The broken bracket can be rewelded by a muffler shop inexpensively.
Mass Airflow Sensor
The mass airflow (MAF) sensor is a small plastic tube with a sensor that fits between the air cleaner box and the intake manifold. This little $300 gem measures the amount of air flowing into the engine to properly set air-fuel mixture for best performance & economy. The sensor typically fails about every 80,000 miles on both diesel and gas W210s. A bad MAF manifests itself with a check engine light (and a more specific computer trouble code) and a very poorly running engine. Sometimes the sensor malfunctions because it is dirty, which can be fixed by a good cleaning. Performance oil-medium air filters like K&N exacerbate the problem because (1) they tend to let more dirt through and (2) they tend to coat the sensor with filter oil.
Although it may be tempting to install a K&N air filter, don’t. The Mercedes air box is well-designed, so the performance gains will be negligible. Moreover, you run the risk of damaging your mass airflow sensor, or worse, your engine. Many people who have their used oil analyzed find higher than normal levels of dirt in the oil (which presumably enters through the intake) when running K&N filters.
Irritations
Squeaky, Creaky Seats
The front seat frames creak on some cars. Unfortunately, replacement frames/rails are expensive. If this bothers you, you’re probably best off rigging something up yourself to tighten it.
Squeaky Power Steering
As one of the bushings on the power steering box wears, it transmits a groan up the steering column every time you turn. The bushing can be replaced, although some dealers may try to sell you a new power steering unit. If you’re looking only to replace the bushing, it’s probably best not to show up wearing your most expensive suit.
Front Sway Bar Links
The front sway bar links wear out somewhat quickly. When worn out, they cause a rattling noise every time you hit bump. You can replace them yourself for about $20 per side.
Sunroof Rattle
The sunroof guides are attached with only one screw on each side. This often rattles and can interfere with the sunroof operation. They should be attached with two screws. The dealer charges a lot of money to put in a second screw. Fix it yourself for less than a dollar.
A/C Blower Regulator
The electronic part that controls the fan speed of the heater and air conditioner fan often burns out in pre-facelift W210s. Mercedes changed the fan design and no longer makes the old regulator. Upgrading the fan and regulator to the newer design costs about $1,000. Inexpensive workaround: the blower regulator from the W140 S-class is a compatible replacement, but its wires are too short. Swap the wiring harnesses with your burned out regulator and install. Total cost: ~$150 and about 45 minutes of your time.
Burned-out Lights
For reasons only explainable by Gottlieb Daimler and Karl Benz, the exterior lightbulbs on some E-class cars like to burn out on what sometimes seems like a weekly schedule. Perhaps its a conspiracy with the lightbulb manufactuers. In any case, the rear taillights tend to be particularly frequent offenders.
Brake Switch
Multiple switches in the brake pedal detect when you apply the brakes. If one of those switches fails, your dash will light up like a Christmas tree with all sorts of errors for the brake assist, traction control and stability control systems when you step on the brake. While uninformed E-class owners may panic about a huge repair bill, well-read people like you will know that the culprit is simply an inexpensive switch that takes only a few minutes to replace.
Rear Brake Rotor Warpage
Mercedes under-spec’d the rear brake rotors. Consequently, they tend to warp prematurely. When they warp, the best solution is to replace the rear rotors with Brembo high performance rotors. The cost is about the same as the replacing with the warp-prone OEM rotors.
Vehicle info and problem particulars:
2000 E430 Sport. Driver's side air blows whatever is outside (i.e., warm/hot). Passenger's side is getting cool, but not as cold as it once did. Slight hissing noise at times behind the vents (i.e., emanating from the engine compartment).
Sensor values:
1 – 92
2 – 102
3 – 92
4 – 86
5 – 92
6 – 198
7 – 16
8 – 141
Error codes:
b1227
b1234
anybody getting any responses ?
I'm in the middle of moving cross-country and will begin addressing
questions once I'm settled back in!
My boyfriend figured out what was wrong with our air conditioner, but I was going to post about our troubles here. I just wanted to say, I think it’s really great what you’re doing. It’s so cool that so many people have responded. You’re very nice!
David- Please help with my 98' E300!? I drive this thing everywhere and I have went 3 weeks without air. Here are the codes:
VALUES
1-32
2-35
3-72
4-71
5-34
6-83
7-24
8-65
CODES
E61 R227
E61 231
E61 232
E61 234
E61 235
E FF
Any help would be greatly appreciated!! I will help you move if you can crack this one. I am driving this thing 1000 miles a week and I am riding in a hot car with hot beer, where would you like me to send it
2001 e320
Sensors
1 – 82
2 – 76
3 – 112
4 – 114
5 – 143
6 – 188
7 – 03
8 – 103
Codes
E61 234
E61 416
E FF
Thank you so much for your help! Help me out and I'll donate to the cause! =)
I released the pressure of my system then recharged with R-134a to about 40psi. The initial read was about 65psi. Can't get anything cold out of my car.
I sure hope you're able to find this post! I'm not sure why it isn't posted on the top/bottom.. It's just floating out here in the middle.. =(
Hi,
Your main problem is a faulty evaporator temperature sensor. It's reporting an implausibly high temperature (#5=143 degrees) which is causing the A/C system to shut down to protect the evaporator core from freezing. The computer does this when it determines that the evap temp sensor is unreliable.
Your refrigerant pressure (#7) looks low. It's hard to say whether your system is adequately charged or not based on pressure alone. Once the compressor is running after replacing that evap temp sensor, you'll have a better idea. Note that you need the compressor engaged in order to charge the system since the (relative) suction from the compressor on the low-side line is needed to draw the refrigerant out of the can.
Blake
thank you so much for your help! i think it's absolutely awesome that you're willing to help out those of us in need! you can expect a few beers from me!!
Hey Blake first, thanks for being such a great resource and money saver, here are my codes:
1-87
2–87
3-85
4-87
5-84
6-136
7-00
8-85
EB1234
EB1241
EFF
Thanks for your help!
Ray,
Looks like your system is empty and needs to be recharged. The
refrigerant pressure sensor is reporting zero pressure. Sometimes this
is caused by a defective sensor, but that happens rarely. Look
through my previous responses for instructions on how to bypass the
pressure sensor and how to reset the codes if you want to give that a
try before recharging.
If your system is empty, the most common source of leak is the receiver-dryer.
Blake
I sent in a question 2 months ago, if you have time could you please check it out and give me some advice. Thanks for any help.
Hey Blake, I have a 1998 E300 TD.
Symptoms are: A tiny bit cold for the first 3-4 minutes, then blows whatever air temp seems to be outside.
First about the faults. I had a bunch of faults that I was able to clear out to a E-FF status with zero showing. A Winter ago I had Firestone replace the Serpentine belt which is where I think the problem might have started. Also checked using my CodeKey ODB reader and no codes thrown.
Here are my error codes, 1st reading is after 3 minutes, 2nd reading after 20 minutes driving to work. These are in Celsius on the left, Fahrenheit on the right in parens:
sensor 1- 37, 36 (98.6, 96.8)
sensor 2- 32, 30 (89.6, 86)
sensor 3- 40, 37 (104, 98.6)
sensor 4- 40, 37 (104, 98.6)
sensor 5- 77, 77 (170.6,170,6)
sensor 6- 37, 95 (98.6, 203)
sensor 7- 08, 08 (bar)
sensor 8- 33, 42 (91.4, 107)
Since sensor 7 reads only 8 bar, so I'm thinking that with no fault codes I might just need a recharge and the problem could be a leak somewhere. A confirmation would help.
Does anyone have a link to the 210 parts numbers for all the sensors?
Thanks in advance,
Jesse
Fairfield, County, Connecticut
Jesse,
In short, your problem is the evaporator temperature sensor (#5). Replace that and you'll be back in business.
Look through my other replies if you are interested in a more comprehensive explanation of why this sensor causes this problem.
Blake
Thanks Blake, I came to the same conclusion last night after adding a can of 134a only to have the compressor blow much colder air for approximately the same short time span of a minute or two,
thanks for your help, donation to the Blake Cameron Wildlife Preservation Fund to follow. :>)
Jesse
Hi Blake,
The E55 has been sitting relatively idle. I have replaced the sensors and had the unit charged. EC light is not on. Air temp sensor in front, even after replacing shows error, though I can read outside temp on instrument cluster.
What's the next step – vacuum leak, head unit, ?
Thanks
John F. Burr, Ph.D.
Continuous Term Lecturer
Krannert School of Management
Purdue University
615 Carrolton Blvd
W. Lafayette, IN 47906
765.404.4114
Mike,
Thanks once again for the beer money. I have good news for you. It looks like all you need is a recharge. None of your error codes are significant. The only one that might make a difference to you is B1231, the engine coolant temperature sensor. That sensor informs the climate control unit when it's appropriate to start blowing (hopefully warm) air after staring the car in the winter.
As for the air conditioner, your refrigerant pressures look good. The vent air is warmer than it should be (40s), but still cool enough (60s) to tell that the A/C is working. Often when the refrigerant is low, you'll hear a hissing noise emanating from behind the center vents and notice a temperature difference between the left and right center vents. A simple recharge should put you back in business. In the interim, you can try using the recirculate button to reduce the temperature of the air being drawn through the AC (assuming the interior is cooler than the outside).
Blake
I have '98 E-320 which gave a problem with the high speed fan motor not comiing on. The blower motor was changed by the dealer a couple of years ago for a hefty sum of $1200. Starting late last year the AC would just not cool. All I am getting is the hot air. I am hesitant to take it to the dealer because the price will vary from $297 (recharge) to may be $4500 (coils replacement). I read your artical and decided to take down the readings and see if could recharge 134a myself. Here are the readings:
#1 30,#2 29, #3 31, #4 31, #5 49, #6 65, #7 01, #8 28.
The error codes are: E61 227, E61 231, E61 233, E61 234, E61 459, E FF, E.
The EC light can be turned off. If you feel that the rfrigerant needs to be recharged, would you let me know the approximate location of the low pressure valve? I have opened the hood andcan see a chrome pipe going from the compressor to the body below the brake fluid cup. This pipe has a valve with a plastic thread cover.
Thanks in anticipation.
SK
I have a '98 E320. Two years ago the high speed blower was replaced by the dealer for a hefty $1200. Late last year, before the Fall, the AC stopped working blowing only hot air. The EC light can be turned off. I was told by the dealer that the recharge will cost me nearly 297 and the worst case scenario is $4500 for changing the coil. I was encouraged to read your article and decided to take down the sensor readiings and the error coses to see if it is indeed just the recharge that is needed. I think I can recharge it myself if I can confirm the location of the low pressure valve. I had looked under the hood and found that the chrome pipe going from the compressor to the dash just below the brake reservoir has a valve with plastic screwed cover.
I have collected the sensor information and the errorcodes per your guidelines. Here they are:
#1 30, #2 29, #3 31, #4 31, #5 49, #6 65, #7 01, #8 28.
The error codes are:
E61 227, E61 231, E61 233, E61 234, E61 459, E FF, E
I will appreciate it if you can put me inthe right directions. Thanks in anticipation.
SK